WEBVTT FILE

Step 28
00:00:01.000 --> 00:00:13.000 line:16 position:50% align:center size:100%
Loosen screws, 2 screws TX 20.

Step 29
00:00:13.000 --> 00:00:17.000 line:16 position:50% align:center size:100%
Remove the cover.

Step 30
00:00:17.000 --> 00:00:27.000 line:16 position:50% align:center size:100%
Only break out as many target break points as there are cables.

Step 31
00:00:27.000 --> 00:00:35.000 line:16 position:50% align:center size:100%
Disconnect the connection to the PV modules.

Step 32
00:00:35.000 --> 00:00:42.000 line:16 position:50% align:center size:100%
Observe the maximum length and diameter of the cables.

Step 33
00:00:42.000 --> 00:00:50.000 line:16 position:50% align:center size:100%
Use cables with the same diameters.

Step 34
00:00:50.000 --> 00:00:55.000 line:16 position:50% align:center size:100%
Switch off the Fronius Solar Battery (OFF).

Step 35
00:00:55.000 --> 00:01:06.000 line:16 position:50% align:center size:100%
Remove 2 fuses of the Fronius Solar Battery.

Step 36
00:01:06.000 --> 00:01:16.000 line:16 position:50% align:center size:100%
Remove 3 - 8 fuses of the battery modules.

Step 37
00:01:16.000 --> 00:01:20.000 line:16 position:50% align:center size:100%
Thread in the BAT+/BAT-/BAT PE cables from below.

Step 38
00:01:20.000 --> 00:01:25.000 line:16 position:50% align:center size:100%
Pull back the BAT cable by 2 cm ... 

Step 39
00:01:25.000 --> 00:01:30.000 line:16 position:50% align:center size:100%
... so that the rubber seals are bulging out.

Step 40
00:01:30.000 --> 00:01:36.000 line:16 position:50% align:center size:100%
Connect the BAT cable to the appropriate terminal point.

Step 41
00:01:36.000 --> 00:01:49.000 line:16 position:50% align:center size:100%
Secure the connected cables with a screwdriver. Observe the printed torque data!

Step 42
00:01:49.000 --> 00:01:58.000 line:16 position:50% align:center size:100%
Refit the 3 - 8 fuses of the battery modules.

Step 43
00:01:58.000 --> 00:02:04.000 line:16 position:50% align:center size:100%
Refit the 2 fuses of the Fronius Solar Battery.

Step 44
00:02:04.000 --> 00:02:11.000 line:16 position:50% align:center size:100%
Switch on the Fronius Solar Battery (ON).

Step 45
00:02:11.000 --> 00:02:30.000 line:16 position:50% align:center size:100%
Secure the cover. 2 x TX 20 screws.

Step 46
00:02:30.000 --> 99:59:59.999 line:16 position:50% align:center size:100%
Connect PV modules. Caution! DC voltage! Note +/-!